Cisco Discussions

Exam 200-301 All Questions

View all questions & answers for the 200-301 exam

Go to Exam

Exam 200-301 topic 1 question 483 discussion

Actual exam question from Cisco's 200-301

Question #: 483
Topic #: 1

[All 200-301 Questions]

Refer to the exhibit. The network engineer is configuring router R2 as a replacement router on the network. After the initial configuration is applied, it is determined that R2 failed to show R1 as a neighbor. Which configuration must be applied to R2 to complete the OSPF configuration and enable it to establish the neighbor relationship with R1?

A. R2(config)#router ospf 1 R2(config-router)#network 192.168.1.0 255.255.255.0 area 2
B. R2(config)#interface g0/0/0 R2(config-if)#ip ospf hello-interval 10
C. R2(config)#interface g0/0/0 R2(config-if)#ip ospf dead-interval 40
D. R2(config)#router ospf 1 R2(config-router)#router-id 192.168.1.2

Show Suggested Answer

Suggested Answer: C 🗳️

by rx78_2 at April 3, 2023, 2:25 p.m.

Comments

Submit Cancel

Arinamohammed

11 months, 3 weeks ago

Selected Answer: C

C is the correct answer

upvoted 1 times

...

TmNvrWts

1 year ago

Selected Answer: C

Since every task needed us to match timers answer is C For the guys getting complicated about router ID-s compare my comment to the picture: R1#192.168.1.1 R2#10.1.1.1 RID is NOT the same. Even the internet address is different on the two router

upvoted 4 times

...

nemostis

1 year, 1 month ago

Selected Answer: D

Pay attention, identical router id on both

upvoted 1 times

...

[Removed]

1 year, 3 months ago

Selected Answer: C

C is correct

upvoted 2 times

...

[Removed]

1 year, 3 months ago

Selected Answer: B

B is correct

upvoted 1 times

[Removed]

1 year, 3 months ago

sorry i meant C

upvoted 2 times

...

...

askar430

1 year, 4 months ago

Selected Answer: D

imposible there are duplicated Router-ID !! , most peoples here focus in timers

upvoted 1 times

askar430

1 year, 4 months ago

oh sorry , my wrong the router-id are diffirents ,

upvoted 1 times

...

...

orenoren

1 year, 5 months ago

but the router id is the same

upvoted 2 times

resoluteq

1 year, 2 months ago

it is not! read the lines carefully, you're mixing the lines.

upvoted 1 times

...

JustToBeFrank

1 year, 4 months ago

I guess people will notice the timer mismatch more than the router IDs.

upvoted 1 times

...

...

berpiy1028

1 year, 9 months ago

Given answer is correct dead timer MUST be match

upvoted 4 times

...

Shanku97

1 year, 9 months ago

is it okay to have different wait timing in two router ?

upvoted 1 times

...

dropspablo

1 year, 10 months ago

Selected Answer: C

Answer is correct. Only change "ip ospf dead-interval 40" in R2

upvoted 3 times

...

rx78_2

2 years, 2 months ago

Selected Answer: B

B and C should both be implemented to achieve the result

upvoted 1 times

studying_1

2 years, 1 month ago

No, on R2 hello timer is 15, so we only need to change the dead timer

upvoted 1 times

studying_1

2 years, 1 month ago

sorry, i meant on R1

upvoted 1 times

...

...

...