exam questions

Exam 300-410 All Questions

View all questions & answers for the 300-410 exam

Exam 300-410 topic 1 question 251 discussion

Actual exam question from Cisco's 300-410
Question #: 251
Topic #: 1
[All 300-410 Questions]


Refer to the exhibit. Clients on ALS2 receive IPv4 and IPv6 addresses, but clients on ALS1 receive only IPv4 addresses and not IPv6 addresses. Which action on
DSW1 allows clients on ALS1 to receive IPv6 addresses?

  • A. Configure DSW1(dhcp-config)#default-router 2002:A04:A01::A04:A01
  • B. Configure DSW1(config-if)#ipv6 dhcp relay destination 2002:404:404::404:404 GigabitEthernet1/2
  • C. Configure DSW1(config)#ipv6 route 2002:404:404::404:404/128 FastEthernet1/0
  • D. Configure DSW1(config-if)#ipv6 helper address 2002:404:404::404:404
Show Suggested Answer Hide Answer
Suggested Answer: B 🗳️

Comments

Chosen Answer:
This is a voting comment (?). It is better to Upvote an existing comment if you don't have anything to add.
Switch to a voting comment New
Brahim90
2 months, 1 week ago
Selected Answer: B
Given answer is correct per cisco book page 75. To relay the DHCPv6 messages to a DHCPv6 server in another network, the local router interface in the network the client belongs to needs to be configured as a DHCPv6 relay agent, using the ipv6 dhcp relay destination interface configuration command. Example 1-24 shows interface Gigabit Ethernet 0/0 configured with the command ipv6 dhcp relay destination 2001:db8:a:b::7, which is used to forward SOLICIT messages to a DHCPv6 server at the address listed. Example 1-24 Configuring R1 as a DHCPv6 Relay Agent R1# config t Enter configuration commands, one per line. End with CNTL/Z. R1(config)# interface gigabitethernet0/0 R1(config-if)# ipv6 dhcp relay destination 2001:db8:a:b::7
upvoted 1 times
...
[Removed]
9 months, 2 weeks ago
Selected Answer: B
B is correct
upvoted 1 times
...
inteldarvid
1 year, 9 months ago
Selected Answer: B
B is correct
upvoted 1 times
...
slcc99
1 year, 10 months ago
Why do ALS2 clients receive IPv6 addresses?
upvoted 1 times
leipeG
6 months, 4 weeks ago
Clients on ALS2 receive IPv6 addresses because DSW1 has been configured with the ipv6 dhcp relay destination command, allowing it to forward IPv6 DHCP requests to the DHCP server.
upvoted 1 times
leipeG
6 months ago
So F0/1 is configured with the ipv6 dhcp relay destination command, and F0/0 is not.
upvoted 2 times
...
...
Rob_CCNP000
1 year, 10 months ago
DSW1 Fa0/0 and Fa0/1 are layer 3 interfaces so both need the dhcp relay configured.
upvoted 2 times
...
...
Community vote distribution
A (35%)
C (25%)
B (20%)
Other
Most Voted
A voting comment increases the vote count for the chosen answer by one.

Upvoting a comment with a selected answer will also increase the vote count towards that answer by one. So if you see a comment that you already agree with, you can upvote it instead of posting a new comment.

SaveCancel
Loading ...
exam
Someone Bought Contributor Access for:
SY0-701
London, 1 minute ago