ExamTopics Logo
Mail Us[email protected]
Menu
Cisco Discussions
exam questions

Exam 200-301 All Questions

View all questions & answers for the 200-301 exam
Go to Exam

Exam 200-301 topic 1 question 1348 discussion

Actual exam question from Cisco's 200-301
Question #: 1348
Topic #: 1
[All 200-301 Questions]

SIMULATION
-


Guidelines
-

This is a lab item in which tasks will be performed on virtual devices

• Refer to the Tasks tab to view the tasks for this lab item.
• Refer to the Topology tab to access the device console(s) and perform the tasks.
• Console access is available for all required devices by clicking the device icon or using the tab(s) above the console window.
• All necessary preconfigurations have been applied.
• Do not change the enable password or hostname for any device.
• Save your configurations to NVRAM before moving to the next item.
• Click Next at the bottom of the screen to submit this lab and move to the next question.
• When Next is clicked the lab closes and cannot be reopened.


Topology
-




Tasks
-

All physical cabling is in place and verified. Connectivity for the Switches on ports E0/1, E0/2, and E0/3 must be configured and available for voice and data capabilities.

1. Configure Sw1 and Sw2 with both VLANS, naming them according to the VLAN Name provided in the topology.
2. Configure the E0/1, E0/2, and E0/3 ports on both switches for both VLANS and ensure that Cisco IP phones and PCs pass traffic.
3. Configure Sw1 and Sw2 to allow neighbor discovery via the vendor-neutral protocol on e0/0.

Show Suggested Answer Hide Answer
Suggested Answer:
by d5c03de at March 7, 2024, 8:25 p.m.

Comments

Chosen Answer:
This is a voting comment (?). It is better to Upvote an existing comment if you don't have anything to add.
Switch to a voting comment New
Submit Cancel
bymrdas
Highly Voted 11 months, 4 weeks ago
Task1 Sw-1 vlan 77 name User_VLAN vlan 177 name Voice_VLAN wr Sw-2 vlan 77 name User_VLAN vlan 177 name Voice_VLAN wr Task2 Sw-1 interface range ethernet0/1-3 switchport mode access switchport access vlan 77 switchport voice vlan 177 wr Sw-2 interface range ethernet0/1-3 switchport mode access switchport access vlan 77 switchport voice vlan 177 wr Task3 Sw-1 lldp run interface ethernet0/0 lldp transmit lldp receive wr Sw-2 lldp run interface ethernet0/0 lldp transmit lldp receive wr
upvoted 5 times
...
KuyaErik101
Most Recent 1 year, 1 month ago
Task 1: Sw1(Config)#vlan 77 Sw1(Config-vlan)#name User_VLAN Sw1(Config)#vlan 177 Sw1(Config-vlan)#name Voice_VLAN Sw2(Config)#vlan 77 Sw2(Config-vlan)#name User_VLAN Sw2(Config)#vlan 177 Sw2(Config-vlan)#name Voice_VLAN Task 2: Sw1(Config)#int range e0/1-3 Sw1(Config-if-range)#switchport mode access Sw1(Config-if-range)#switchport access vlan 77 Sw1(Config-if-range)# switchport voice vlan 177 Sw2(Config)#int range e0/1-3 Sw2(Config-if-range)#switchport mode access Sw2(Config-if-range)#switchport access vlan 77 Sw2(Config-if-range)# switchport voice vlan 177 Task 3: Sw1(Config)#lldp run Sw1(Config)#int range e0/1 - 3 Sw1(Config)#no lldp transmit Sw1(Config)#no lldp receive wr mem Sw2(Config)#lldp run Sw2(Config)#int range e0/1 - 3 Sw2(Config)#no lldp transmit Sw2(Config)#no lldp receive write memory
upvoted 3 times
matass_md
9 months ago
no lldp transmit / receive you input that command in the interface mode not global configuration (config-if) . but here we are asked to make it up for interface e0/0 so i would add interface e0/0 lldp transmit lldp receive apply this on both switches .
upvoted 1 times
...
...
d5c03de
1 year, 2 months ago
Task 1: Sw1(Config)#vlan 77 Sw1(Config-vlan)#name User_VLAN Sw1(Config)#vlan 177 Sw1(Config-vlan)#name Voice_VLAN Sw2(Config)#vlan 77 Sw2(Config-vlan)#name User_VLAN Sw2(Config)#vlan 177 Sw2(Config-vlan)#name Voice_VLAN Task 2: Sw1(Config)#int range e0/1-3 Sw1(Config-if-range)#switchport mode access Sw1(Config-if-range)#switchport access vlan 77 Sw1(Config-if-range)# switchport voice vlan 177 Sw2(Config)#int range e0/1-3 Sw2(Config-if-range)#switchport mode access Sw2(Config-if-range)#switchport access vlan 77 Sw2(Config-if-range)# switchport voice vlan 177 Task 3: Sw1(Config)#lldp run Sw2(Config)#lldp run write memory
upvoted 3 times
86a50a6
1 year, 2 months ago
add lldp transmit receive command on interface level on both sides
upvoted 2 times
MalikMak
1 year, 2 months ago
No by default it's in transmit and receive as soon as you do lldp run, however he should disable transmit and receive on all the other interfaces as the task didn't mention the other ports but only e0/0 Sw1(Config)#lldp run Sw1(Config)#int range e0/1 - 3 Sw1(Config)#no lldp transmit Sw1(Config)#no lldp receive Sw2(Config)#lldp run Sw2(Config)#int range e0/1 - 3 Sw2(Config)#no lldp transmit Sw2(Config)#no lldp receive
upvoted 2 times
86a50a6
1 year, 1 month ago
you are correct about lldp automatically deploying trans receiv on all ports when activated, however, i wonder if it is necessary to deny them on other ports since this is not stated in the question
upvoted 5 times
...
...
...
...
Community vote distribution
A (35%)
C (25%)
B (20%)
Other
Most Voted
A voting comment increases the vote count for the chosen answer by one.

Upvoting a comment with a selected answer will also increase the vote count towards that answer by one. So if you see a comment that you already agree with, you can upvote it instead of posting a new comment.

SaveCancel
exam
Someone Bought Contributor Access for:
SY0-701
London, 1 minute ago