Exam 200-301 topic 1 question 1376 discussion

Actual exam question from Cisco's 200-301

Question #: 1376
Topic #: 1

SIMULATION
-

Guidelines
-

This is a lab item in which tasks will be performed on virtual devices.

• Refer to the Tasks tab to view the tasks for this lab item.
• Refer to the Topology tab to access the device console(s) and perform the tasks.
• Console access is available for all required devices by clicking the device icon or using the tab(s) above the console window.
• All necessary preconfigurations have been applied.
• Do not change the enable password or hostname for any device.
• Save your configurations to NVRAM before moving to the next item.
• Click Next at the bottom of the screen to submit this lab and move to the next question.
• When Next is clicked, the lab doses and cannot be reopened.

Topology
-

Tasks
-

All physical cabling is in place and verified. Connectivity for the Switches on ports E0/1, E0/2, and E0/3 must be configured and available for voice and data capabilities.

1. Configure Sw1 and Sw2 with the VLAN naming as indicated.
2. Assign the VLANs to the appropriate interfaces and set a non-trunking, non-tagged, single-VLAN for each interface according to the topology.
3. Configure both switches to use the L2 vendor-neutral discovery protocol to broadcast device information, including the native VLAN across the e0/0 interfaces.

Show Suggested Answer

Suggested Answer:

by MinSun600 at Sept. 12, 2024, 3:24 a.m.

Comments

Submit Cancel

MicroDiff

6 months, 3 weeks ago

SW1 (config)# vlan 77 name IT_User_VLAN vlan 88 name HR_User_VLAN vlan 177 IT_Voice_VLAN vlan 188 name HR_Voice_VLAN wr SW2 (config)#vlan 77 name IT_User_VLAN vlan 88 name HR_User_VLAN vlan 177 IT_Voice_VLAN vlan 188 name HR_Voice_VLAN wr SW1 (config)#interface e0/1-2 switchport mode access switchport access vlan 77 interface e0/1 switchport mode access switchport voice vlan 177 interface e0/3 switchport mode access switchport acces vlan 88 switchport voice vlan 188 wr SW2 (config)# interface e0/3 switchport mode access switchport access vlan 77 interface e0/1 switchport mode access switchport access vlan 88 switchport voice vlan 188 interface e0/2 switchport mode access switchport voice vlan 177 wr SW1 (config)# lldp run wr SW2 (config)# lldp run wr

upvoted 2 times

...

3040636

7 months, 2 weeks ago

1. sw1-sw2 vl 77 name IT-User_VLAN vl 88 name HR_User_VLAN vl 177 name IT_Voice_VLAN vl 188 name HR_Voice_VLAN 2. sw1 e0/1 sw mo acc sw acc vl 77 sw voice vl 177 e1/2 sw mo acc sw acc vl 77 e0/3 sw mo acc sw acc vl 88 sw voice vl 188 sw2 e0/3 sw mo acc sw acc vl 77 e0/2 sw mo acc sw voice vl 177 e0/1 sw mo acc sw acc vl 88 sw voice vl 188 3. sw1-sw2 lldp run e0/0 lldp tr lldp rx

upvoted 2 times

...

MinSun600

7 months, 3 weeks ago

on task 3 i believe the correct solution should be on SW1 and SW2 as it is saying on interface E0/0 be SW1(config)#int E0/0 sw1(config-if)#lldp run write memory SW2(config)#int E0/0 sw2(config-if)#lldp run write memory

upvoted 2 times

...

MinSun600

7 months, 3 weeks ago

there's mistakes on task 1 the vlan of voice put is as USER and on task 2 the switchport of voice vlan put it as switchport access vlan 177 , 188 on sw1 and sw2 while it should be on sw2 int E0/1 sw2(config-if)#switchport mode access sw2(config-if)#switchport voice vlan 177 same for vlan 188 as it is voice too not ad Data and on SW1 for voice vlans should be same so corrected and notice between the DATA vlans and the VOICE Vlans be careful students

upvoted 1 times

exiledwl

7 months, 1 week ago

I really dont know what you are trying to say, but your output is wrong for SW2 e0/1 it should look like this: Sw2#e0/1 sw mo acc sw acc vl 88 sw voice vl 188

upvoted 1 times

...

Exam 200-301 All Questions

View all questions & answers for the 200-301 exam

Exam 200-301 topic 1 question 1376 discussion

Comments

MicroDiff

3040636

MinSun600

MinSun600

exiledwl

SY0-701