exam questions

Exam 200-301 All Questions

View all questions & answers for the 200-301 exam

Exam 200-301 topic 1 question 356 discussion

Actual exam question from Cisco's 200-301
Question #: 356
Topic #: 1
[All 200-301 Questions]


Refer to the exhibit. The loopback1 interface of the Atlanta router must reach the loopback3 interface of the Washington router. Which two static host routes must be configured on the New York router? (Choose two.)

  • A. ipv6 route 2000::3/128 s0/0/0
  • B. ipv6 route 2000::1/128 s0/0/1
  • C. ipv6 route 2000::1/128 2012::1
  • D. ipv6 route 2000::1/128 2012::2
  • E. ipv6 route 2000::3/128 2023::3
Show Suggested Answer Hide Answer
Suggested Answer: CE 🗳️

Comments

Chosen Answer:
This is a voting comment (?). It is better to Upvote an existing comment if you don't have anything to add.
Switch to a voting comment New
SOAPGUY
Highly Voted 2 years, 5 months ago
Selected Answer: CE
ON NEWYORK ON NEWYORK ON NEWYORK~~~
upvoted 17 times
...
[Removed]
Highly Voted 2 years, 4 months ago
To let the serial interfaces on the Atlanta and Washington routers reach other, you need to configure a static host route (on the New York router) which points to the destination IP (to the serial interface of the other router) and goes through the next-hop IP address. For the Washington Lo3, you have to specify a static route to 2000::3/128 (destination IP) through Se0/0/0 on the Washington router (the next-hop): ipv6 route 2000::3/128 2023::3 For the Atlanta Lo1, you have to specify a static route to 2000::1/128 (destination IP) through Se0/0/0 on the Atlanta router (the next-hop): ipv6 route 2000::1/128 2012::1 command on the Washington router A. ipv6 route 2000::3/128 s0/0/0 Wrong answer. B. ipv6 route 2000::1/128 s0/0/1 Wrong answer. C. ipv6 route 2000::1/128 2012::1 Correct answer. D. ipv6 route 2000::1/128 2012::2 Wrong answer. E. ipv6 route 2000::3/128 2023::3 Correct answer.
upvoted 7 times
JonasWolfxin
2 years, 3 months ago
Both static host routes must be configured on the New York router
upvoted 4 times
...
...
[Removed]
Most Recent 7 months, 3 weeks ago
Selected Answer: CE
C & E are correct
upvoted 2 times
...
cormorant
1 year, 10 months ago
THE NEXT HOPS ARE THE INTERFACES ON THE ATLANTA AND WASHINGTON ROUTERS. ATLANTA: SERIAL 0/0/0 2012::1/126 WASHINGTON: SERIAL SE0/0/0 - 2023::3/126
upvoted 2 times
...
ludodelauz
2 years, 9 months ago
Why it's C and not D ?
upvoted 1 times
J0k3r07
10 months ago
great question
upvoted 1 times
...
...
helmerpach
2 years, 10 months ago
is corresct because is static
upvoted 1 times
...
Anarckii
2 years, 11 months ago
the answers are correct but technically A and B are as well
upvoted 1 times
daddydagoth
1 year, 8 months ago
They aren't correct my friend. You might have misread the question like I did and are configuring routes on Atlanta and Washington to reach each other instead of New Yourk's router like the question asks you to!
upvoted 1 times
...
panagiss
2 years, 11 months ago
No, take a look at the interfaces on A & B
upvoted 2 times
Darrien1301
2 years, 6 months ago
can you explain that in more detail? Dont understand why this isnt possible
upvoted 1 times
Deeztroyer
2 years, 4 months ago
the serial interfaces are swapped around...
upvoted 1 times
...
...
...
...
Hodicek
2 years, 11 months ago
i would choose D - E
upvoted 3 times
...
jerry19
3 years, 6 months ago
Answer C and E, it would be much easier if the question said configure recursive route on New York router for each loopback network.
upvoted 6 times
...
oooMooo
3 years, 6 months ago
C and E are correct. ipv6 [loopback network] [serial interface IP] IPv6: /128 provides a single IPv6 address.
upvoted 3 times
...
Robin999
3 years, 8 months ago
I need to correct my Statement. Given Answers are correct. They should not communicate to each other, just from one side to the other side.
upvoted 2 times
...
Robin999
3 years, 8 months ago
Correct answers are AB because the next Hop addresses are not matching in CD.
upvoted 4 times
...
ZayaB
3 years, 9 months ago
According to what I understand, you can use interface names such as s0/0/0 or g0/1 on a static route config instead of next hop IP addresses. It is not recommended but it is possible. Therefore, A and B is technically correct, isn't it?
upvoted 3 times
ZayaB
3 years, 9 months ago
Sorry, it is asking the config on NY router...C and E is correct. My bad.
upvoted 7 times
...
...
Community vote distribution
A (35%)
C (25%)
B (20%)
Other
Most Voted
A voting comment increases the vote count for the chosen answer by one.

Upvoting a comment with a selected answer will also increase the vote count towards that answer by one. So if you see a comment that you already agree with, you can upvote it instead of posting a new comment.

SaveCancel
Loading ...
exam
Someone Bought Contributor Access for:
SY0-701
London, 1 minute ago