Exam 300-410 topic 1 question 201 discussion

B,C,D are valid commands, A hasn't presented in IOS reference. It seems B,C are best for answer. https://www.cisco.com/c/en/us/td/docs/ios-xml/ios/debug/command/a1/db-a1-cr-book/db-c1.html

Per cisco book page 906 choice B&C are correct.

In the ETA file the D one seems to be debug condition ip. If you find that then is B and D otherwise the answer is fine. For me D in the simultations is debug condition ip, cause this exists as a command I prefer it rather then debug confition session-id ADJCHG Remember also this: The debug condition session-id command filters a session only after the session has been established. The session identifier is a unique dynamic number generated internally by the Cisco IOS software and assigned to each session when the session is established. https://www.cisco.com/c/en/us/td/docs/ios-xml/ios/isg/configuration/xe-3s/asr1000/isg-xe-3s-asr1000-book/isg-debug-dcd.html Hope that you are gonna smash the exam. Se ya

look at HungarianDish comment. Debug session-id IS a valid command But I think you have to turn on a session: IOU2#show subscriber session %No active Subscriber Sessions IOU2# page 4 here says debug session-id is valid command https://www.cisco.com/c/en/us/td/docs/ios-xml/ios/debug/command/a1/db-a1-cr-book/db-c1.html B and C However B doesn't mean session-id it means OSPF Adjacency. Look: %OSPF-5-ADJCHG: Process 1, Nbr 10.1.1.1 on TenGigabitEthernet2/1 from FULL to DOWN, Neighbor Down: Too many retransmissions We receive the above output with this command: debug ip ospf adj

B & C are correct https://www.cisco.com/c/en/us/td/docs/ios-xml/ios/isg/configuration/xe-3s/asr1000/isg-xe-3s-asr1000-book/isg-debug-dcd.pdf (page 4)

debug condition session-id not exist in devices

B and C are the correct ones !

Its B and C, Why? B is logical and C (https://www.cisco.com/c/en/us/td/docs/ios-xml/ios/isg/configuration/xe-3s/asr1000/isg-xe-3s-asr1000-book/isg-debug-dcd.pdf)

I do not see the "debug condition session-id" command to be related to troubleshooting an OSPF adjacency issue. They probably meant this command: #debug ip ospf adj

debug condition seems ot be the only valid answer here... except i am missing something site1#debug condition ? called called number calling calling cpl Cisco Provisioning Language debugging glbp interface group interface interface ip IP address mac-address MAC address match-list apply the match-list profile Media Services Profile standby interface group username username vcid VC ID vrf Virtual Routing and Forwarding xconnect Xconnect conditional debugging on segment pair

https://www.cisco.com/c/en/us/td/docs/ios-xml/ios/isg/configuration/xe-3s/asr1000/isg-xe-3s-asr1000-book/isg-debug-dcd.pdf debug condition session-id

Can't find the "debug condition session-id ADJCHG" command. Running a 7200 Software (C7200-ADVENTERPRISEK9-M), Version 15.2(4)M7. Sometimes I'm amazed with these questions. Are we really expected to pass with this ton of hit or miss questions? Not referring to examtopics just Cisco questions are worded poorly and designed bad.

R2#debug condition ? called called number calling calling cpl Cisco Provisioning Language debugging glbp interface group interface interface ip IP address mac-address MAC address match-list apply the match-list profile Media Services Profile standby interface group username username vcid VC ID vrf Virtual Routing and Forwarding xconnect Xconnect conditional debugging on segment pair R2#debug condition

sw#debug condition os? % Unrecognized command sw#debug condition session-id ? <1-4294967295> Session Number for debug filtering

B & C: I checked Cisco IOS and IOS-XE and only B & C are valid commands.

The other commands are not valid. Only 2 commands valid are C and D.

Correct: BC