ExamTopics Logo
Mail Us[email protected]
Menu
Cisco Discussions
exam questions

Exam 300-430 All Questions

View all questions & answers for the 300-430 exam
Go to Exam

Exam 300-430 topic 1 question 62 discussion

Actual exam question from Cisco's 300-430
Question #: 62
Topic #: 1
[All 300-430 Questions]

The Cisco Hyperlocation detection threshold is currently set to -50 dBm. After reviewing the wireless user location, discrepancies have been noticed. To improve the Cisco Hyperlocation accuracy, an engineer attempts to change the detection threshold to -100 dBm. However, the Cisco Catalyst 9800 Series Wireless
Controller does not allow this change to be applied. What actions should be taken to resolve this issue?

  • A. Disable Cisco Hyperlocation, change the Cisco Hyperlocation detection threshold, and then enable it.
  • B. Create a new profile on Cisco CMX with the new Cisco Hyperlocation detection range, and apply it on the WLAN.
  • C. Place the APs to monitor mode, shutdown the radios, and then change the Cisco Hyperlocation detection threshold.
  • D. Shutdown all radios on the controller, change the Cisco Hyperlocation detection range, and enable the radios again.
Show Suggested Answer Hide Answer
Suggested Answer: A 🗳️
by kthekillerc at Dec. 29, 2021, 9:48 p.m.

Comments

Chosen Answer:
This is a voting comment (?). It is better to Upvote an existing comment if you don't have anything to add.
Switch to a voting comment New
Submit Cancel
Guglielmino
Highly Voted 3 years, 1 month ago
In your document https://www.cisco.com/c/en/us/td/docs/wireless/controller/9800/17-1/config-guide/b_wl_17_11_cg/cisco-hyperlocation.html: "Restrictions on Cisco Hyperlocation It is not possible to modify detection, trigger, and reset thresholds while Hyperlocation is in enabled state." So the correct answer is A
upvoted 17 times
...
rrahim
Most Recent 2 months, 1 week ago
Selected Answer: A
A. Disable Cisco Hyperlocation, change the Cisco Hyperlocation detection threshold, and then enable it. To change the Cisco Hyperlocation detection threshold on a Cisco Catalyst 9800 Series Wireless Controller, you must first disable Cisco Hyperlocation, make the necessary changes, and then re-enable it. This is because certain settings, like the detection threshold, cannot be modified while Hyperlocation is active.
upvoted 1 times
...
riktammenaars
6 months, 1 week ago
Selected Answer: A
https://www.cisco.com/c/en/us/td/docs/wireless/controller/9800/17-1/config-guide/b_wl_17_11_cg/cisco-hyperlocation.html#restrictions-on-hyperlocation
upvoted 1 times
...
Ocsicccnp
7 months ago
Selected Answer: A
It is not possible to modify detection, trigger, and reset thresholds while Hyperlocation is in enabled state.
upvoted 1 times
...
JimDiGriz
2 years ago
Selected Answer: A
It is not possible to modify detection, trigger, and reset thresholds while Hyperlocation is in enabled state.
upvoted 2 times
...
kthekillerc
3 years, 2 months ago
Selected Answer: B
Believe answer should be B
upvoted 2 times
anonymonkey
3 years, 1 month ago
Think you were right the first time. https://www.cisco.com/c/en/us/td/docs/wireless/controller/9800/17-1/config-guide/b_wl_17_11_cg/cisco-hyperlocation.html
upvoted 4 times
...
...
kthekillerc
3 years, 4 months ago
Provided answer is correct
upvoted 1 times
...
Community vote distribution
A (35%)
C (25%)
B (20%)
Other
Most Voted
A voting comment increases the vote count for the chosen answer by one.

Upvoting a comment with a selected answer will also increase the vote count towards that answer by one. So if you see a comment that you already agree with, you can upvote it instead of posting a new comment.

SaveCancel
exam
Someone Bought Contributor Access for:
SY0-701
London, 1 minute ago