ExamTopics Logo
Mail Us[email protected]
Menu
Cisco Discussions
exam questions

Exam 350-801 All Questions

View all questions & answers for the 350-801 exam
Go to Exam

Exam 350-801 topic 1 question 201 discussion

Actual exam question from Cisco's 350-801
Question #: 201
Topic #: 1
[All 350-801 Questions]

Callers from a branch report getting busy tones intermittently when trying to reach colleagues in other office branches during peak hours. An engineer collects
Cisco CallManager service traces to examine the situation. The traces show:
50805567.000 |07:35:39.676 |SdlSig |StationOutputDisplayNotify |restart0 |StationD(1,100,63,6382) |StationCdpc(1,100,64,4725) |1,100,40,7.101980^*^* |
[R:N-H:0,N:0,L:0,V:0,Z:0,D:0] TimeOutValue=10 Status=x807 UnicodeStatus= Locale=1 50805567.001 |07:35:39.676 |AppInfo | StationD: (0006382)
DisplayNotify timeOutValue=10 notify='x807' content='Not Enough Bandwidth' ver=85720014.
What should be fixed to resolve the issue?

  • A. class of service configuration
  • B. geolocation configuration
  • C. region configuration
  • D. codec configuration
Show Suggested Answer Hide Answer
Suggested Answer: C 🗳️
by ciscogeek at May 9, 2022, 2:52 p.m.

Comments

Chosen Answer:
This is a voting comment (?). It is better to Upvote an existing comment if you don't have anything to add.
Switch to a voting comment New
Submit Cancel
G0y0
1 month, 3 weeks ago
Selected Answer: C
D. is totally incorrect. When when you are configuring regions in the CUCM, you do not select a codec specifically; rather, you set the per-call bandwidth rate that is allowed between each site. You can place a video call using 480p30 resolution at 384 kbps or at 2 Mbps. However, using a higher codec can provided better efficiency and thus consume less bandwidth. In this case, obviously C. is correct.
upvoted 1 times
...
b3532e4
7 months, 1 week ago
At the "peak time" ----> Not Enough Bandwidth. In my opinion Codec configuration
upvoted 1 times
G0y0
1 month, 3 weeks ago
And where would you configure the codecs?
upvoted 1 times
...
...
AgshinA
1 year, 1 month ago
Selected Answer: C
The issue indicated by the “Not Enough Bandwidth” message in the Cisco CallManager service traces suggests that the available bandwidth for calls between the branches is being exceeded during peak hours. To resolve this issue, you should: Check and Adjust Locations and Regions: Verify the configuration of locations and regions in Cisco CallManager to ensure that they are set up correctly and that there is enough allocated bandwidth for the number of expected concurrent calls between the branches1. Use Low Bandwidth Codecs: Consider configuring low bandwidth codecs like G.729 or G.723 for calls between the branches to reduce the amount of bandwidth each call consumes1.
upvoted 2 times
...
lpicardin
2 years, 1 month ago
Selected Answer: C
Answer C
upvoted 2 times
...
AAMM
2 years, 11 months ago
answer is B
upvoted 1 times
AAMM
2 years, 11 months ago
sorry for that it is C the correct answer
upvoted 2 times
...
...
ciscogeek
2 years, 12 months ago
Selected Answer: C
Class of Service is Partition/CSS which cannot solve the issue. Region Configuration can set the maximum audio bit rate. There is no page in CUCM called 'Codec' configuration, but it makes the question confusing. I would go with Region Config.
upvoted 4 times
...
Community vote distribution
A (35%)
C (25%)
B (20%)
Other
Most Voted
A voting comment increases the vote count for the chosen answer by one.

Upvoting a comment with a selected answer will also increase the vote count towards that answer by one. So if you see a comment that you already agree with, you can upvote it instead of posting a new comment.

SaveCancel
exam
Someone Bought Contributor Access for:
SY0-701
London, 1 minute ago