ExamTopics Logo
Mail Us[email protected]
Menu
Cisco Discussions
exam questions

Exam 200-301 All Questions

View all questions & answers for the 200-301 exam
Go to Exam

Exam 200-301 topic 1 question 308 discussion

Actual exam question from Cisco's 200-301
Question #: 308
Topic #: 1
[All 200-301 Questions]


Refer to the exhibit. Switch A is newly configured. All VLANs are present in the VLAN database. The IP phone and PC A on Gi0/1 must be configured for the appropriate VLANs to establish connectivity between the PCs. Which command set fulfills the requirement?

  • A. SwitchA(config-if)#switchport mode access SwitchA(config-if)#switchport access vlan 50 SwitchA(config-if)#switchport voice vlan 51
  • B. SwitchA(config-if)#switchport mode trunk SwitchA(config-if)#switchport trunk allowed vlan add 50, 51 SwitchA(config-if)#switchport voice vlan dot1p
  • C. SwitchA(config-if)#switchport mode trunk SwitchA(config-if)#switchport trunk allowed vlan 50, 51 SwitchA(config-if)#mis qos trust cos
  • D. SwitchA(config-if)#switchport mode access SwitchA(config-if)#switchport access vlan 50 SwitchA(config-if)#switchport voice vlan untagged
Show Suggested Answer Hide Answer
Suggested Answer: A 🗳️
by Goh0503 at Sept. 16, 2022, 2:56 p.m.

Comments

Chosen Answer:
This is a voting comment (?). It is better to Upvote an existing comment if you don't have anything to add.
Switch to a voting comment New
Submit Cancel
Goh0503
Highly Voted 2 years, 8 months ago
Answer A https://networklessons.com/cisco/ccna-routing-switching-icnd1-100-105/voice-vla First, we have to create the two VLANs: SW1(config)#vlan 100 SW1(config-vlan)#name COMPUTER SW1(config-vlan)#exit SW1(config)#vlan 101 SW1(config-vlan)#name VOIP SW1(config-vlan)#exit Now we can configure the interface: SW1(config)#interface GigabitEthernet 0/1 SW1(config-if)#switchport mode access SW1(config-if)#switchport access vlan 100 SW1(config-if)#switchport voice vlan 101 SW1(config-if)#exit We configure the interface in access mode and use VLAN 100 for the computer. The switchport voice vlan command tells the switch to use VLAN 101 as the voice VLAN.
upvoted 18 times
...
Dronep
Most Recent 8 months, 1 week ago
My concern here is the part in the question stated that All Vlans are present "All VLANs are present in the VLAN database" If that is the case shouldn't we use add?
upvoted 1 times
Cham1
4 months, 2 weeks ago
VLANS are already created , so you need to ONLY add them to interface. Capiche?
upvoted 1 times
...
...
[Removed]
1 year, 2 months ago
Selected Answer: A
A is correct
upvoted 1 times
...
FALARASTA
2 years, 1 month ago
Any port configured as trunk should be eliminated first voice is configures in access ports only. The right answer is A
upvoted 3 times
...
iMo7ed
2 years, 3 months ago
Selected Answer: A
It is A
upvoted 1 times
...
JJY888
2 years, 3 months ago
There was a question earlier where the correct answer was a truck and not access. This question clears up that confusion. Voice Vlan should be an access port.
upvoted 1 times
Shanku97
1 year, 9 months ago
voice vlan is always access port, any option of voice vlan being trunk should get eliminated at first !!
upvoted 1 times
...
...
[Removed]
2 years, 7 months ago
Selected Answer: A
Answer A is correct
upvoted 1 times
...
Community vote distribution
A (35%)
C (25%)
B (20%)
Other
Most Voted
A voting comment increases the vote count for the chosen answer by one.

Upvoting a comment with a selected answer will also increase the vote count towards that answer by one. So if you see a comment that you already agree with, you can upvote it instead of posting a new comment.

SaveCancel