ExamTopics Logo
Mail Us[email protected]
Menu
Cisco Discussions
exam questions

Exam 200-301 All Questions

View all questions & answers for the 200-301 exam
Go to Exam

Exam 200-301 topic 1 question 276 discussion

Actual exam question from Cisco's 200-301
Question #: 276
Topic #: 1
[All 200-301 Questions]


Refer to the exhibit. An engineer has started to configure replacement switch SW1. To verify part of the configuration, the engineer issued the commands as shown and noticed that the entry for PC2 is missing. Which change must be applied to SW1 so that PC1 and PC2 communicate normally?

  • A. SW1(config)#interface fa0/2 SW1(config-if)#no switchport access vlan 2 SW1(config-if)#no switchport trunk allowed vlan 3 SW1(config-if)#switchport trunk allowed vlan 2
  • B. SW1(config)#interface fa0/2 SW1(config-if)#no switchport access vlan 2 SW1(config-if)#switchport trunk native vlan 2 SW1(config-if)#switchport trunk allowed vlan 3
  • C. SW1(config)#interface fa0/2 SW1(config-if)#no switchport mode trunk SW1(config-if)#no switchport trunk allowed vlan 3 SW1(config-if)#switchport mode access
  • D. SW1(config)#interface fa0/1 SW1(config-if)#no switchport access vlan 2 SW1(config-if)#switchport access vlan 3 SW1(config-if)#switchport trunk allowed vlan 2
Show Suggested Answer Hide Answer
Suggested Answer: C 🗳️
by Goh0503 at Oct. 2, 2022, 8:21 a.m.

Comments

Chosen Answer:
This is a voting comment (?). It is better to Upvote an existing comment if you don't have anything to add.
Switch to a voting comment New
Submit Cancel
Goh0503
Highly Voted 2 years, 7 months ago
Answer C access port – a port that can be assigned to a single VLAN. This type of interface is configured on switch ports that are connected to end devices such as workstations, printers, or access points. trunk port – a port that is connected to another switch. This type of interface can carry traffic of multiple VLANs, thus enabling you to extend VLANs across your entire network. Frames are tagged by assigning a VLAN ID to each frame as they traverse between switches. https://study-ccna.com/access-and-trunk-ports/
upvoted 12 times
...
Bhrino
Highly Voted 1 year, 12 months ago
Selected Answer: C
C is correct there’s no need to use trunk ports due the fact they are all in the same vlan and c just removes all the trunking commands and adds the last access port one
upvoted 5 times
...
[Removed]
Most Recent 1 year, 1 month ago
Selected Answer: C
C is correct
upvoted 1 times
...
ananinamia
1 year, 8 months ago
But where vlan3 comes what is relation with this question?
upvoted 4 times
c9957e3
9 months, 3 weeks ago
11 months late, but for anybody else wondering, VLAN3 was configured as shown in the run config, though there is no VLAN 3 connected to the interface.
upvoted 1 times
...
...
iMo7ed
2 years, 2 months ago
Selected Answer: C
C is correct
upvoted 2 times
...
Community vote distribution
A (35%)
C (25%)
B (20%)
Other
Most Voted
A voting comment increases the vote count for the chosen answer by one.

Upvoting a comment with a selected answer will also increase the vote count towards that answer by one. So if you see a comment that you already agree with, you can upvote it instead of posting a new comment.

SaveCancel
exam
Someone Bought Contributor Access for:
SY0-701
London, 1 minute ago