exam questions

Exam 200-301 All Questions

View all questions & answers for the 200-301 exam

Exam 200-301 topic 1 question 537 discussion

Actual exam question from Cisco's 200-301
Question #: 537
Topic #: 1
[All 200-301 Questions]

An engineer is configuring NAT to translate the source subnet of 10.10.0.0/24 to any one of three addresses: 192.168.3.1, 192.168.3.2, or 192.168.3.3. Which configuration should be used?

  • A. enable configure terminal ip nat pool mypool 192.168.3.1 192.168.3.3 prefix-length 30 access-list 1 permit 10.10.0.0 0.0.0.255 ip nat outside destination list 1 pool mypool interface g1/1 ip nat inside interface g1/2 ip nat outside
  • B. enable configure terminal ip nat pool mypool 192.168.3.1 192.168.3.3 prefix-length 30 access-list 1 permit 10.10.0.0 0.0.0.254 ip nat inside source list 1 pool mypool interface g1/1 ip nat inside interface g1/2 ip nat outside
  • C. enable configure terminal ip nat pool mypool 192.168.3.1 192.168.3.3 prefix-length 30 route map permit 10.10.0.0 255.255.255.0 ip nat outside destination list 1 pool mypool interface g1/1 ip nat inside interface g1/2 ip nat outside
  • D. enable configure terminal ip nat pool mypool 192.168.3.1 192.168.3.3 prefix-length 30 access-list 1 permit 10.10.0.0 0.0.0.255 ip nat inside source list 1 pool mypool interface g1/1 ip nat inside interface g1/2 ip nat outside
Show Suggested Answer Hide Answer
Suggested Answer: D 🗳️

Comments

Chosen Answer:
This is a voting comment (?). It is better to Upvote an existing comment if you don't have anything to add.
Switch to a voting comment New
splashy
Highly Voted 1 year, 9 months ago
Selected Answer: D
D is the least incorrect, but still very not correct lol: prefix length 30 = 255.255.255.253 = 4-2 hosts = 2 hosts It actually "works" in PT but you have the broadcast address in your range which is no bueno. Prefix should be /29
upvoted 9 times
splashy
1 year, 9 months ago
255.255.255.253 must be ...252 ... typo
upvoted 4 times
NICE_ANSWERS
1 year, 4 months ago
Why must the prefix length be 29 to make the configuration fully correct? And why is /30 not advisable?
upvoted 2 times
...
...
...
[Removed]
Most Recent 7 months, 1 week ago
Selected Answer: D
D is correct
upvoted 1 times
...
houssembenali
11 months, 3 weeks ago
to be able to translate the whole /24 subent you will need the overload in the end of each ip nat command, in the config stated above, nat will translate only 3 addresses from the whole subnet
upvoted 1 times
...
Request7108
1 year, 10 months ago
I didn't see it at first but B is wrong because the wildcard written ends in .254 which is a valid mask but not a valid wildcard
upvoted 1 times
...
Goh0503
2 years ago
Answer is D https://study-ccna.com/dynamic-nat/
upvoted 2 times
...
Community vote distribution
A (35%)
C (25%)
B (20%)
Other
Most Voted
A voting comment increases the vote count for the chosen answer by one.

Upvoting a comment with a selected answer will also increase the vote count towards that answer by one. So if you see a comment that you already agree with, you can upvote it instead of posting a new comment.

SaveCancel
Loading ...
exam
Someone Bought Contributor Access for:
SY0-701
London, 1 minute ago