ExamTopics Logo
Mail Us[email protected]
Menu
Cisco Discussions
exam questions

Exam 300-715 All Questions

View all questions & answers for the 300-715 exam
Go to Exam

Exam 300-715 topic 1 question 166 discussion

Actual exam question from Cisco's 300-715
Question #: 166
Topic #: 1
[All 300-715 Questions]

While configuring Cisco TrustSec on Cisco IOS devices, the engineer must set the CTS device ID and password in order for the devices to authenticate with each other. However, after this is complete, the devices are not able to properly authenticate. What issue would cause this to happen even if the device ID and passwords are correct?

  • A. EAP-FAST is not enabled.
  • B. The SGT mappings have not been defined.
  • C. The device aliases are not matching.
  • D. The devices are missing the configuration cts credentials trustsec verify 1.
Show Suggested Answer Hide Answer
Suggested Answer: A 🗳️
by tobnix at Dec. 15, 2022, 11:45 a.m.

Comments

Chosen Answer:
This is a voting comment (?). It is better to Upvote an existing comment if you don't have anything to add.
Switch to a voting comment New
Submit Cancel
tliz
Highly Voted 1 year, 2 months ago
Selected Answer: A
I believe A is the correct answer. This question appears to be calling out NDAC which uses EAP-FAST. It's not B because SGT mappings don't have anything to do with devices authenticating to each other. It's not C because I don't think there is a device alias concept in TrustSec It's not D because this command doesn't exist as far as I can tell.
upvoted 6 times
...
west33637
Highly Voted 1 year, 3 months ago
A seems like the only logical answer to me.
upvoted 5 times
Gago77
1 year, 2 months ago
the Cisco TrustSec device ID and password for this switch to use when authenticating with other Cisco TrustSec devices with EAP-FAST.
upvoted 1 times
...
...
XBfoundX
Most Recent 5 months ago
I go with A. Device# cts credentials id device-id password password Specifies the Cisco TrustSec device ID and password for this switch to use when authenticating with other Cisco TrustSec devices with EAP-FAST. The device-id argument has a maximum length of 32 characters and is case sensitive. https://www.cisco.com/c/en/us/td/docs/switches/lan/trustsec/configuration/guide/trustsec/ident-conn_config.html
upvoted 3 times
...
DeviantSpy
11 months, 1 week ago
Selected Answer: A
Agree with west33637 and tliz.
upvoted 1 times
...
Cnoteone
1 year, 1 month ago
Selected Answer: D
cts credentials Use the cts credentials command in privileged EXEC mode to specify the TrustSec ID and password of the network device. Use the clear cts credentials command to delete the credentials.
upvoted 1 times
Cnoteone
1 year, 1 month ago
https://www.cisco.com/c/en/us/td/docs/switches/lan/trustsec/configuration/guide/trustsec/command_sum.html#85930
upvoted 1 times
...
flambadone
6 months, 4 weeks ago
I don't think this is correct. The question implies this is done with 'However, after this is complete' - because the last sentence says 'you have to use a username and password'. Personally I'm going with A
upvoted 1 times
...
...
tobnix
1 year, 4 months ago
Selected Answer: B
Should be B
upvoted 1 times
...
Community vote distribution
A (35%)
C (25%)
B (20%)
Other
Most Voted
A voting comment increases the vote count for the chosen answer by one.

Upvoting a comment with a selected answer will also increase the vote count towards that answer by one. So if you see a comment that you already agree with, you can upvote it instead of posting a new comment.

SaveCancel
exam
Someone Bought Contributor Access for:
SY0-701
London, 1 minute ago