ExamTopics Logo
Mail Us[email protected]
Menu
Fortinet Discussions
exam questions

Exam NSE7_SDW-7.2 All Questions

View all questions & answers for the NSE7_SDW-7.2 exam
Go to Exam

Exam NSE7_SDW-7.2 topic 1 question 70 discussion

Actual exam question from Fortinet's NSE7_SDW-7.2
Question #: 70
Topic #: 1
[All NSE7_SDW-7.2 Questions]

Refer to the exhibits.


Exhibit A -




Exhibit B -



Exhibit A shows the configuration for an SD-WAN rule and exhibit B shows the respective rule status, the routing table, and the member status.

The administrator wants to understand the expected behavior for traffic matching the SD-WAN rule.

Based on the exhibits, what can the administrator expect for traffic matching the SD-WAN rule?

  • A. The traffic will be load balanced across all three overlays.
  • B. The traffic will be routed over T_INET_1_0.
  • C. The traffic will be routed over T_INET_0_0.
  • D. The traffic will be routed over T_MPLS_0.
Show Suggested Answer Hide Answer
Suggested Answer: B 🗳️
by thepresidents83 at Oct. 10, 2024, 5:47 p.m.

Comments

Chosen Answer:
This is a voting comment (?). It is better to Upvote an existing comment if you don't have anything to add.
Switch to a voting comment New
Submit Cancel
f002a32
2 months, 1 week ago
Selected Answer: D
When you use "set gateway enable" in a FortiGate SD-WAN member configuration, it bypasses the usual FIB lookup process. Instead of relying on the forwarding information base to determine the next-hop based on the destination IP, the device uses the explicitly configured gateway address from the SD-WAN member settings. This provides more predictable routing behavior and ensures that traffic is directed through the intended gateway, regardless of what the routing table might otherwise dictate
upvoted 2 times
1d21e23
3 weeks ago
"set default" is still "disable", which means the requirement for a FIB best match which returns an sdwan member as the destination interface is still in place.
upvoted 1 times
...
...
ReyAndres619
3 months ago
Selected Answer: D
Services rule 1 set gateway enable, : this instructs Fortigate to skip the FIB lookup, and instead use the gateway address that you configured in the SD-WAN member settings ( PAG 173 7.2)
upvoted 2 times
...
k3rnelpanicpj
3 months, 3 weeks ago
Selected Answer: B
Routing for 10.0.0.0/8 is using T_INET_1_0 and T_INET_0_0. SLA shows that T_INET_1_0 has SLA0x1 which is better than SLA0x0 fot T_INET_0_0
upvoted 2 times
...
kappa915
5 months, 2 weeks ago
Selected Answer: B
B is correct
upvoted 1 times
...
ccie8122
6 months ago
Selected Answer: B
SD-WAN strategy is Lowest Cost (SLA) due to the "set mode sla" command. SG p226-228: member 5 meets both SLA targets; member 4 meets only one of the SLA targets, and member 3 meets neither SLA target. On that basis, member 5 (T_MPLS_0) will get all traffic matching the "Corp" SD-WAN rule.
upvoted 2 times
ccie8122
6 months ago
Hit submit too soon. Except for the fact that member 5 does not have a route to the destination which is a requirement. Thus the next best member is 4. Thus T_INET_1_0 gets all traffic matching the rule. B is correct.
upvoted 3 times
...
...
thepresidents83
6 months, 3 weeks ago
Selected Answer: B
T_MPLS is the best member (it matches more sla), but there's no route to destination 10.0.0.0/8. Therefore, the next member that meet sla requirement and have a route for the destination is selected (T_INET_1_0)
upvoted 4 times
...
Community vote distribution
A (35%)
C (25%)
B (20%)
Other
Most Voted
A voting comment increases the vote count for the chosen answer by one.

Upvoting a comment with a selected answer will also increase the vote count towards that answer by one. So if you see a comment that you already agree with, you can upvote it instead of posting a new comment.

SaveCancel
exam
Someone Bought Contributor Access for:
SY0-701
London, 1 minute ago