Exam 70-741 topic 1 question 69 discussion

Actual exam question from Microsoft's 70-741

Question #: 69
Topic #: 1

HOTSPOT -
You are configuring internal virtual networks to support multitenancy communication between tenant virtual machine networks and remote sites.
You have a tenant named Tenant1.
You need to enable Border Gateway Protocol (BGP) for Tenant1.
Which commands should you run? To answer, select the appropriate options in the answer area.
NOTE: Each correct selection is worth one point.
Hot Area:

Show Suggested Answer

Suggested Answer:

References: https://docs.microsoft.com/en-us/windows-server/remote/remote-access/bgp/border-gateway-protocol-bgp

by TMW at June 7, 2019, 12:37 a.m.

Comments

Submit Cancel

dan

Highly Voted 6 years ago

again, the questions are from the real test and you can not insert your own answers. you can not assume anything either - look at the link they provided and it reads just like they put it for the answer

upvoted 32 times

...

[Removed]

Highly Voted 6 years ago

Dan is right, you can not assume or insert your thoughts. You got to use what is presented to in the questions. Here a reference straight out of Microsoft reference. By the way the answer is also correct. $Contoso_RoutingDomain = "ContosoTenant" $Fabrikam_RoutingDomain = "FabrikamTenant" Install-RemoteAccess -MultiTenancy Enable-RemoteAccessRoutingDomain -Name $Contoso_RoutingDomain -Type All -PassThru Enable-RemoteAccessRoutingDomain -Name $Fabrikam_RoutingDomain -Type All -PassThru

upvoted 15 times

...

panda

Most Recent 4 years, 6 months ago

Since the question says "multitenancy", Install-RemoteAccess must have Multitenancy parameter and next cmdlet should be Enable-RemoteAccessRoutingDomain.(*1) When it doesn't say so, it may have -VpnType parameter and next one could Add-BgpRoute.(*2) (*1)https://docs.microsoft.com/en-us/windows-server/remote/remote-access/bgp/border-gateway-protocol-bgp (*2)https://docs.microsoft.com/en-us/windows-server/networking/dns/deploy/anycast

upvoted 2 times

panda

4 years, 6 months ago

Now I think the given answers are correct.

upvoted 2 times

...

panda

4 years, 5 months ago

The question says that "you need to enable BGP for Tenant1". Taht means that since you have already added BGP router, you want to manage BGP. Therefore, Add-BgpRouter can be excluded.

upvoted 1 times

...

ykarma

4 years, 7 months ago

Not sure if i got this on the exam but pay attention to it. Had my exam Nov 27th 2020

upvoted 2 times

...

adasko

4 years, 10 months ago

Answer is correct as per: https://docs.microsoft.com/en-us/windows-server/remote/remote-access/bgp/border-gateway-protocol-bgp Install-RemoteAccess -MultiTenancy Enable-RemoteAccessRoutingDomain -Name $Contoso_RoutingDomain -Type All -PassThru Enable-RemoteAccessRoutingDomain -Name $Fabrikam_RoutingDomain -Type All -PassThru

upvoted 3 times

...

TMW

6 years ago

This one is incorrect, here is what I have in my notes I took: Powershell command to install/configure BGP: On side one server side: 1 - Add-BgpRouter -BgpIdentifier 192.168.1.100 -LocalASN 65000 (ip address is the local address of the server you are configuring it on) 2 - Add-BgpPeer -name SRV2-Nug -LocalIPAddress 192.168.1.100 -PeerIPAddress 192.168.1.102 -LocalASN 65000 -PeerASN 65000 -PeeringMode Automatic On side two server side: 1 - Add-BgpRouter -BgpIdentifier 192.168.1.102 -LocalASN 65000 (ip address is the local address of the server you are configuring it on) 2 - Add-BgpPeer -name DC-nug -LocalIPAddress 192.168.1.102 -PeerIPAddress 192.168.1.100 -LocalASN 65000 -PeerASN 65000 -PeeringMode Automatic

upvoted 1 times

...