Welcome to ExamTopics
ExamTopics Logo
- Expert Verified, Online, Free.
Mail Us [email protected]
Menu
sale

Want to Unlock All Questions for this Exam?

Full Exam Access, Discussions, No Robots Checks

27
Students signed up in the last 24H

Avaya 7303 Exam Actual Questions

The questions for 7303 were last updated on April 7, 2024.
  • Viewing page 1 out of 17 pages.
  • Viewing questions 1-4 out of 72 questions
 

Topic 1 - Single Topic

Question #1 Topic 1

A technician is installing a 600r, and notices that the server boots to the Windows screen then starts booting again. It is stuck in a boot. What is the first step that should be taken?

  • A. Re-image the server.
  • B. Open a case requesting a replacement server.
  • C. Replace the hard drive.
  • D. Verify the SCSI terminator or tape drive is properly connected to the server.
Reveal Solution Hide Solution   Discussion  

Correct Answer: B 🗳️

Question #2 Topic 1

A technician has completed the configuration and programming for an implementation of a new Avaya CallPilot system. When the Avaya CallPilot is rebooted, over which local Area Network (LAN) connection does the Communication Server 1000 communicate with the Avaya CallPilot voicemail system?

  • A. DSO
  • B. CLAN
  • C. ELAN
  • D. SLAN
  • E. TLAN
Reveal Solution Hide Solution   Discussion  

Correct Answer: C 🗳️

Question #3 Topic 1

A company is planning to install a new Avaya CallPilot RIs. 5.0 system. They need a high availability system that will allow a standby server to lake over in case the primary server fails. Which hardware platform should be delivered on-site?

  • A. 703t
  • B. 600r
  • C. 1006r
  • D. 1002rp
  • E. 2250
Reveal Solution Hide Solution   Discussion  

Correct Answer: C 🗳️

Question #4 Topic 1

A technician is installing an Avaya CallPilot with the NTRH40CA MBP96 CAT5 board and two NTRB18DA Mgate cards. When cabling the NTRB18DA Mgate cards in a Communication Server 1000S Media Gateway, which statement describes the cabling configuration that is the most valid?

  • A. Attach the customer supplied RJ-45 cables to the face of the Mgate cards and then to the MBP96 card.
  • B. Attach the customer supplied RJ-45 cables to the backplane of the Media Gateway or Media Gateway expansion cabinet and then to the MBP96 card.
  • C. Attach NTDU0609 cables to the face of the Mgate cards and route them outside the Media Gateway. Then couple the customer supplied RJ-45 cables from the NTDU0609 to the MPB96 cards.
  • D. Attach the NTDU0609 cables to the face of the Mgate cards and take them outside the Media ay lo a customer supplied Ethernet hub. Attach RJ-45 cable from the hub to the MPB96 cards.
Reveal Solution Hide Solution   Discussion  

Correct Answer: C 🗳️

Next Questions

Get IT Certification

Unlock free, top-quality video courses on ExamTopics with a simple registration. Elevate your learning journey with our expertly curated content. Register now to access a diverse range of educational resources designed for your success. Start learning today with ExamTopics!

Start Learning for free
Community vote distribution
A (35%)
C (25%)
B (20%)
Other
Most Voted
A voting comment increases the vote count for the chosen answer by one.

Upvoting a comment with a selected answer will also increase the vote count towards that answer by one. So if you see a comment that you already agree with, you can upvote it instead of posting a new comment.

SaveCancel