ExamTopics Logo
Mail Us[email protected]
Menu
 

300-080 Actual Exam Questions

Last updated on Dec. 10, 2024.
Vendor:Cisco
Exam Code:300-080
Exam Name:Troubleshooting Cisco IP Telephony and Video (CTCOLLAB)
Exam Questions:157
97% Passed the exam with this material
 

Topic 1 - Single Topic

Question #1 Topic 1

An IP phone that is connected through a Cisco Catalyst 3750 Series Switch is failing to register with the subscriber as a backup server. When the user presses the settings button on the phone, only the Cisco Unified Communications Manager publisher shows as registered. What is the most likely cause for this issue?

  • A. The phone does not have the correct Cisco Unified Communications Manager group in the device configuration page.
  • B. The Cisco Unified Communications Manager group that is applied through the device pool is misconfigured.
  • C. The ip-helper address command for the subscriber is not configured on the switch port.
  • D. The subscriber does not have the correct device pool configured.
  • E. The enterprise phone configuration does not have the call control redundancy enabled.
Reveal Solution Hide Solution   Discussion  

Correct Answer: B 🗳️

Question #2 Topic 1

Refer to the exhibit.

An IP phone that is connected through a Cisco Catalyst 3750 Series Switch is failing to register with Cisco Unified Communications Manager. When the user presses the settings button on the phone, the Operational VLAN ID shows a blank entry. What is the most likely cause for this issue?

  • A. The switch may not be supplying inline power.
  • B. The spanning tree portfast command needs to be removed.
  • C. The trunk encapsulation is missing. The trunk must be configured for dot1.Q.
  • D. Cisco Discovery Protocol is disabled on the switch.
  • E. The Operational VLAN ID of the phone always shows as blank. The Admin. VLAN ID should be 110.
Reveal Solution Hide Solution   Discussion  

Correct Answer: D 🗳️

Question #3 Topic 1

You configured a Cisco ISR G2 as a SIP gateway, but the gateway does not show that it is registered with Cisco Unified Communications Manager. What is causing this issue?

  • A. Cisco Unified Communications Manager does not support SIP gateways.
  • B. The gateway does not have the UC license installed.
  • C. The gateway does not have Cisco Unified Border Element session licensing.
  • D. Cisco Unified Communications Manager does not show a SIP gateway as registered if it is not properly configured.
  • E. Cisco Unified Communications Manager never shows a SIP gateway as registered even when it is properly configured.
  • F. The Cisco ISR G2 cannot be a SIP gateway.
Reveal Solution Hide Solution   Discussion  

Correct Answer: E 🗳️

Question #4 Topic 1

Which issue would cause an MGCP gateway to fail to register with Cisco Unified Communications Manager?

  • A. missing the configuration command isdn bind-l3 ccm-manager under the ISDN interface
  • B. mismatched domain name on the MGCP gateway and Cisco Unified Communications Manager gateway configuration
  • C. misconfigured route group in Cisco Unified Communications Manager
  • D. incorrect MGCP IP address specified in the gateway configuration in Cisco Unified Communications Manager
Reveal Solution Hide Solution   Discussion  

Correct Answer: B 🗳️

file Viewing page 1 out of 40 pages.
Viewing questions 1-4 out of 157 questions
Next Questions
Browse atleast 50% to increase passing rate cup
Community vote distribution
A (35%)
C (25%)
B (20%)
Other
Most Voted
A voting comment increases the vote count for the chosen answer by one.

Upvoting a comment with a selected answer will also increase the vote count towards that answer by one. So if you see a comment that you already agree with, you can upvote it instead of posting a new comment.
exam
Someone Bought Contributor Access for:
SY0-701
London, 1 minute ago