300-206 Exam - Free Actual Q&As, Page 1

300-206 Actual Exam Questions

Last updated on Dec. 5, 2024.

Vendor:Cisco

Exam Code:300-206

Exam Name:CCNP Security Implementing Cisco Edge Network Security Solutions (SENSS)

Exam Questions:368

Topic 1 - Single Topic

Question #1 Topic 1

All 30 users on a single floor of a building are complaining about network slowness. After investigating the access switch, the network administrator notices that the MAC address table is full (10,000 entries) and all traffic is being flooded out of every port. Which action can the administrator take to prevent this from occurring?

A. Configure port-security to limit the number of mac-addresses allowed on each port
B. Upgrade the switch to one that can handle 20,000 entries
C. Configure private-vlans to prevent hosts from communicating with one another
D. Enable storm-control to limit the traffic rate
E. Configure a VACL to block all IP traffic except traffic to and from that subnet

Reveal Solution Discussion

Correct Answer: A 🗳️

Question #2 Topic 1

A network printer has a DHCP server service that cannot be disabled. How can a layer 2 switch be configured to prevent the printer from causing network issues?

A. Remove the ip helper-address
B. Configure a Port-ACL to block outbound TCP port 68
C. Configure DHCP snooping
D. Configure port-security

Reveal Solution Discussion

Correct Answer: C 🗳️

Question #3 Topic 1

A switch is being configured at a new location that uses statically assigned IP addresses. Which will ensure that ARP inspection works as expected?

A. Configure the 'no-dhcp' keyword at the end of the ip arp inspection command
B. Enable static arp inspection using the command 'ip arp inspection static vlan vlan-number
C. Configure an arp access-list and apply it to the ip arp inspection command
D. Enable port security

Reveal Solution Discussion

Correct Answer: C 🗳️

Question #4 Topic 1

Which of the following would need to be created to configure an application-layer inspection of SMTP traffic operating on port 2525?

A. A class-map that matches port 2525 and applying an inspect ESMTP policy-map for that class in the global inspection policy
B. A policy-map that matches port 2525 and applying an inspect ESMTP class-map for that policy
C. An access-list that matches on TCP port 2525 traffic and applying it on an interface with the inspect option
D. A class-map that matches port 2525 and applying it on an access-list using the inspect option

Reveal Solution Discussion

Correct Answer: A 🗳️

Question #5 Topic 1

Which command is used to nest objects in a pre-existing group?

A. object-group
B. network group-object
C. object-group network
D. group-object

Reveal Solution Discussion

Correct Answer: D 🗳️

Question #6 Topic 1

Which threat-detection feature is used to keep track of suspected attackers who create connections to too many hosts or ports?

A. complex threat detection
B. scanning threat detection
C. basic threat detection
D. advanced threat detection

Reveal Solution Discussion

Correct Answer: B 🗳️

Question #7 Topic 1

What is the default behavior of an access list on the Cisco ASA security appliance?

A. It will permit or deny traffic based on the access-list criteria.
B. It will permit or deny all traffic on a specified interface.
C. An access group must be configured before the access list will take effect for traffic control.
D. It will allow all traffic.

Reveal Solution Discussion

Correct Answer: C 🗳️

Question #8 Topic 1

What is the default behavior of NAT control on Cisco ASA Software Version 8.3?

A. NAT control has been deprecated on Cisco ASA Software Version 8.3.
B. It will prevent traffic from traversing from one enclave to the next without proper access configuration.
C. It will allow traffic to traverse from one enclave to the next without proper access configuration.
D. It will deny all traffic.