Welcome to ExamTopics
ExamTopics Logo
- Expert Verified, Online, Free.
 

Juniper JN0-664 Exam Actual Questions

The questions for JN0-664 were last updated on July 22, 2024.
  • Viewing page 1 out of 24 pages.
  • Viewing questions 1-4 out of 96 questions

Topic 1 - Exam A

Question #1 Topic 1

Click the Exhibit button.

R2 is receiving the same route from R1 and R3. You must ensure that you can load balance traffic for that route.
Referring to the exhibit, which configuration change will allow load balancing?

  • A. Configure the multipath parameter under the global BGP configuration.
  • B. Apply the prepend policy as an import policy under group R1.
  • C. Configure the multipath multiple-as parameter under the global BGP configuration.
  • D. Apply the prepend policy as an import policy under group R3.
Reveal Solution Hide Solution   Discussion   2

Correct Answer: C 🗳️

Question #2 Topic 1

Click the Exhibit button.

You are troubleshooting the connection between AS 64496 and AS 64497 and notice that only one of the paths is being used for traffic forwarding.
Referring to the exhibit, which three actions will ensure that R1 is configured properly for load balancing BGP routes? (Choose three.)

  • A. Verify that the routing table on R1 has BGP routes for 203.0.113.128/25 with multiple next hops.
  • B. Verify that the multipath option is configured under protocols bgp on both R2 and R3.
  • C. Verify that there is a load balancing export policy under routing-options for the received BGP routes on R1.
  • D. Verify that the multipath option is configured under protocols bgp on R1.
  • E. Verify that an import load balancing policy exists under protocols bgp for the received BGP routes on R1.
Reveal Solution Hide Solution   Discussion   5

Correct Answer: ABD 🗳️

Question #3 Topic 1

After a recent power outage, your manager asks you to investigate ways to automatically reduce the impact caused by suboptimal routing in your OSPF and OSPFv3 network after devices reboot.
Which three configuration statements accomplish this task? (Choose three.)

  • A. set protocols ospf3 realm ipv4-unicast overload timeout 900
  • B. set protocols ospf overload
  • C. set protocols ospf overload timeout 900
  • D. set protocols ospf3 overload
  • E. set protocols ospf3 overload timeout 900
Reveal Solution Hide Solution   Discussion   6

Correct Answer: CDE 🗳️

Question #4 Topic 1

You are configuring anycast RP for load balancing and redundancy in your PIM-SM domain. You want to share active sources between RPs.
In this scenario, what are two solutions that will accomplish this task? (Choose two.)

  • A. Configure MSDP on each RP router.
  • B. Configure anycast PIM with the rp-set statement on each RP router.
  • C. Configure anycast PIM with the rp-set statement on each source DR router.
  • D. Configure MSDP on each source DR router.
Reveal Solution Hide Solution   Discussion   4

Correct Answer: AB 🗳️

Community vote distribution
A (35%)
C (25%)
B (20%)
Other
Most Voted
A voting comment increases the vote count for the chosen answer by one.

Upvoting a comment with a selected answer will also increase the vote count towards that answer by one. So if you see a comment that you already agree with, you can upvote it instead of posting a new comment.

SaveCancel
Loading ...
ex Want to SAVE BIG on Certification Exam Prep?
close
ex Unlock All Exams with ExamTopics Pro 75% Off
  • arrow Choose From 1000+ Exams
  • arrow Access to 10 Exams per Month
  • arrow PDF Format Available
  • arrow Inline Discussions
  • arrow No Captcha/Robot Checks
Limited Time Offer
Ends in