ExamTopics Logo
Mail Us[email protected]
Menu
Cisco Discussions
exam questions

Exam 350-601 All Questions

View all questions & answers for the 350-601 exam
Go to Exam

Exam 350-601 topic 1 question 488 discussion

Actual exam question from Cisco's 350-601
Question #: 488
Topic #: 1
[All 350-601 Questions]

An engineer must configure port aggregation between two Cisco MDS 9000 Series Switches. The solution must meet these requirements:
• Suspend member interface if parameters mismatch.
• Load-balance traffic on multiple ports.
• Support traffic from multiple VSANs.

Which port channel configuration must be used?

  • A. Port type: FT Port -
    Port channel mode: Active
  • B. Port type: F Port -
    Port channel mode: On
  • C. Port type: E Port -
    Port channel mode: Active
  • D. Port type: TE Port -
    Port channel mode: On
Show Suggested Answer Hide Answer
Suggested Answer: D 🗳️
by Arch_Angel at Feb. 19, 2024, 12:25 p.m.

Comments

Chosen Answer:
This is a voting comment (?). It is better to Upvote an existing comment if you don't have anything to add.
Switch to a voting comment New
Submit Cancel
Manu_75
2 months, 2 weeks ago
Selected Answer: C
- has to be an Edge port between two switches - has to use mode active to detect mismatched parameter Port type TE is not "configured" - there is no "switchport type te" command. It's "switchport type e" and "switchport trunk mode on" that result in a TE port.
upvoted 2 times
...
Rollizo
10 months, 2 weeks ago
Selected Answer: D
D: - Need to pass several VSAN then TE - Port-channel mode ON, because if there is mismatch parameters the port is suspended. (in case active mode, the port is isolated)
upvoted 2 times
...
madelesm
11 months, 2 weeks ago
Selected Answer: D
it must be a TE port
upvoted 1 times
...
elper
1 year, 1 month ago
Selected Answer: D
https://www.cisco.com/en/US/docs/switches/datacenter/mds9000/sw/6_2/configuration/guides/int/nx-os/pc.html#wp1072515
upvoted 1 times
...
GoForCCNP
1 year, 1 month ago
Selected Answer: D
I agree with Arch_Angel, P1Z7C and SysAd, correct answer is D. Just check the Table 6-1 in the link provided by P1Z7C!
upvoted 1 times
...
asd248402
1 year, 3 months ago
Selected Answer: A
port mode must be active to suspend the link
upvoted 1 times
...
asd248402
1 year, 3 months ago
Selected Answer: A
Port channel need to be active in order to suspend and the FT is in reality TF port that can be connected to a NPV switch It can be connected to another trunked N port (TN port) or trunked NP port (TNP port) to create a link between a core switch and an NPV switch or a host bus adapter (HBA) in order to carry tagged frames.
upvoted 2 times
...
JobProcess
1 year, 3 months ago
Selected Answer: D
Answer is D
upvoted 2 times
...
Arch_Angel
1 year, 4 months ago
Answer is D Moves interfaces to the suspended state if its operational values are incompatible with the port channel
upvoted 4 times
P1Z7C
1 year, 1 month ago
https://www.cisco.com/en/US/docs/switches/datacenter/mds9000/sw/6_2/configuration/guides/int/nx-os/pc.html on mode - Moves interfaces to the suspended state if its operational values are incompatible with the PortChannel. active mode - Moves interfaces to the isolated state if its operational values are incompatible with the PortChannel.
upvoted 3 times
...
SysAd
1 year, 4 months ago
yes, and TE carries multiple vsan
upvoted 1 times
...
...
Community vote distribution
A (35%)
C (25%)
B (20%)
Other
Most Voted
A voting comment increases the vote count for the chosen answer by one.

Upvoting a comment with a selected answer will also increase the vote count towards that answer by one. So if you see a comment that you already agree with, you can upvote it instead of posting a new comment.

SaveCancel